Dump Garbage Truck

1.The product function is introduced as follows

(1)Its main feature is simple and efficient garbage collection. Good environmental protection, high vehicle utilization efficiency, widely suitable for sanitation, municipal, factory and mining enterprises, property communities, garbage and concentrated residential areas, urban streets garbage treatment, with sealing self-unloading function, hydraulic operation, convenient dumping garbage.

(2)Plate configuration: the new standard national six model, Foton H2 dump garbage truck, optional engine 115 horsepower, diesel 152 horsepower, equipped with 5 gear gearbox, 3300 wheelbase, 700 wire tire, air brake, optional with air conditioning, yellow card, our company free to provide all the vehicle registration procedures and invoices.

(3)Upper configuration:

Component parts: The dump garbage truck is composed of domestic famous brand original chassis (national joint guarantee), box device, force collector, multi-channel directional valve, hydraulic lifting mechanism, hydraulic system, operating system, etc.

2.The picture of the vehicle is as follows

3.Detailed parameters of the vehicle are as follows

4.The top decomposition picture display

5.Product use precautions

(1)The use and maintenance of the chassis and engine parts shall be carried out according to the provisions of the chassis instruction manual.

(2)In the running-in stage of the new car, the range is 1500-2500 Km and the unloading within 900 times, the loading capacity is 70% of the rated load mass, and the engine shall not slam the throttle when unloading.

(3) After working for 300 times, the working oil should be replaced. Unscrew the hydraulic oil release plug, put the old oil, then tighten the oil release plug, inject new oil from the upper refueling hole, and then start the engine, increase the stroke step by step, and run each cylinder twice to confirm that the work is reliable.

(4) High-pressure oil tubing is replaced regularly every two years. In the use of found crack, damage, shoulder expansion and other phenomena, should be replaced in time.

(5) Check the hydraulic system for oil leakage frequently. And timely repair and replace the oil seal.

(6)The lubrication of automotive General Motors lithium based grease (GB5671-85) can be driven from the oil nozzle until the clearance. Cheng Li Special purpose Vehicle Co., LTD.

(7)Clean the surface of the vehicle and chassis after the operation every day. Check the hydraulic oil stock regularly, regularly add lubricating oil to each moving part, and apply lubricating oil to the surface of each guide rail.

(8)Check and adjust the working pressure of the gear oil pump regularly; check the oil filter element, remove the surface impurities or replace the filter element; replace the hydraulic oil regularly.

6. Matters need attention

(1)If the hydraulic system is found with abnormal movement during operation, it should immediately stop the work, analyze the cause and eliminate the fault. Do not force the operation.

(2)For both the force carrier and the multiple switching valve, the garbage must not enter the driving state.

(3)The pressure regulating device of the hydraulic system is the pressure regulating bolt on the multi-channel reversing valve. After the pressure regulating device is adjusted and locked, the bolt shall not be transferred at will. Users are not allowed to adjust the oil pressure casually.

(4)When the case is loaded, fast landing is not allowed, and its slow descent should be controlled by manipulating the reversing valve.

(5)When lifting the drawing box due to oil change, cleaning and maintenance, the box pole must be supported to prevent the sudden drop of the box and the accident.

(6) When unloading the box, the flat and solid ground should be selected to stop and the box should rise slowly with the discharge of the material to avoid the vehicle roll or lift the front.

(7)Do not flush the water into the hydraulic oil tank when washing the car. Check the height of the hydraulic oil surface frequently, fill the hydraulic oil when the oil is insufficient, all oil joints shall not leak oil.

(8)The maintenance should prevent collision, avoid parts damage, deformation and scratches and other assembly parts must be cleaned.seven. Hydraulic system fault judgment and treatment when the hydraulic mechanism is not working properly. First, check whether the force collector is properly engaged, whether the hydraulic oil in the tank is sufficient, and whether the suction pipe ball valve is fully open.

(9)The hydraulic mechanism is not moving. Please follow the following steps:

a.Whether the oil quantity in the hydraulic oil tank is sufficient. Hydraulic oil should be filled when insufficient;

b.Observe whether the oil intake pipe from the oil tank to the oil pump is caused by the boom oil suction phenomenon due to the old inclination. If there is this phenomenon, the oil inlet pipe should be replaced;

c.Check for the gear oil pump failure. Install a pressure gauge, screw the regulating bolts, observe whether the gauge pressure reaches the specified value;

d.If all the pressure regulating bolts do not reach the specified oil pressure after twisting, the gear oil pump fails and the gear oil pump must be replaced;

e. If the gear oil pump works normally, it is the multi-channel reversing valve core blocked. The spool should be removed to clear impurities and use.

(10)The mechanism moves but is unable to check whether the gear oil pump fails and whether the system pressure reaches the specified value.

(11)The hydraulic mechanism moves slowly to check whether the gear oil pump failure, oil filter, oil filter core isDon't plug.

(12)After-sales service "three guarantees" period is really due to quality reasons, our company implements repair.

(13)The following items do not belong to the scope of "three guarantees": Not maintained during the mandatory departure period; b, the vehicle fails; c, the vehicle (including driving without license and violation); d, without the consent of the Company, E. Remove the assembly or parts into parts without the consent of the company, And the origin and unable to confirm the responsibility and cause analysis; f, the accident vehicle without the consent of the company or identification; g, the vehicle due to improper adjustment or no inspection adjustment; h, low-value consumable and vulnerable parts (such as electrical appliances, glass, rubber, plastic products, etc.); All kinds of parts, bearings.

(14)For vehicles that do not fall within the scope of "three guarantees", our company is responsible for the users and provide convenient maintenance services, but should charge appropriate fees. Your reasonable suggestions of this product or other products, please propose to my after-sales service department, so that the factory can adopt in time, the factory all staff to express the most sincere thanks to you!

(15)a.Certificate of dump garbage truck b.Operation manual of dump garbage truck c.chassis certificate d.chassis manual e.vehicle tools

7.Company scale display (part) picture

8.Workshop process picture (part) display

9.Model user use function picture display