Small Cleaning And Suction Truck
The cleaning and suction truck has the functions of flushing, dredging, suction, and reverse discharge.
Efficient cleaning: The cleaning and suction truck is equipped with a high-pressure water gun and a suction device,
which can quickly and effectively remove dirt, oil stains, and other difficult to clean pollutants from the ground.
This efficient cleaning method not only saves a lot of time and manpower, but also ensures the cleaning effect.
Protecting the environment: During the cleaning process of the sewage suction truck, sewage and pollutants can be
sucked into the vehicle for treatment or discharge, avoiding direct discharge of sewage into the environment and
reducing environmental pollution. This is of great significance for protecting the urban environment and ecological
balance.
Reduce labor costs: Using cleaning and suction trucks can greatly reduce the need for manual cleaning and lower
labor costs. Meanwhile, automation and mechanization have also reduced the complexity and labor intensity of
manual operations.
The working principle of the sewage suction truck:
Due to the continuous immersion of the fecal suction hose on the liquid surface,
the air inside the fecal tank becomes thinner and thinner as it cannot be
replenished. As a result, the pressure inside the tank is lower than atmospheric
pressure, and the fecal liquid enters the tank through the fecal suction hose under
atmospheric pressure. Or due to the proximity of the siphon tube to the bottom
of the tank, when air is continuously discharged into the manure tank, it is
compressed because there is no way out, causing the pressure inside the tank
to be higher than atmospheric pressure. The manure liquid is discharged outside
the tank through the siphon tube and suction hose under the action of compressed
air.
【Technical parameters of the entire vehicle】 | |||
Product trademark | Xiangnongda brand | Product model | 348 |
Product Name |
Tank volume (m3) | SGW5040GQWBJ6 | |
Total mass (Kg) | 4495 | External dimensions (mm) | 1.71 |
Rated load capacity (Kg) | 1305 | Cargo size (mm) | 5230×1810×2430 |
Curb weight (Kg) | 3060 | Total mass of quasi trailer (Kg) | ×× |
Rated passenger capacity (person) | Maximum load capacity of saddle (Kg) | ||
Cab capacity (persons) | 2 | Front/rear suspension (mm) | |
Approach Angle/Departure Angle (degrees) | 18/14 | Maximum speed (km/h) | 1115/1515 |
Axle load (Kg) | 1710/2785 | Product model | 110 |
remarks | The purpose of this vehicle is for suction cleaning, with the main devices being the tank and pump ABS model: CM4YL, ABS manufacturer: Guangzhou Ruili Kemi Automotive Electronics Co., Ltd. The side rear protection is welded with Q235 material, and the rear protection section size (mm) is 100 × 50. The height of the rear protection above the ground (mm) is 335. The tank size is (straight section length x diameter) (mm): 2500 × 1100; The sewage tank body (straight section length x diameter) (mm) is 2100 x 1100, and the clean water tank body (straight section length x diameter) (mm) is 400 x 1100; The cross-section of the clear water tanks on both sides is composed of arcs and polygons, and the external dimensions (maximum) (length × width × height) are 2100 × 490X650 Effective volume of sewage tank: 1.71 cubic meters, medium: liquid waste, density: 800 kg/cubic meter, effective volume of clean water tank: 1.32 cubic meters, transport medium: water, density: 1000 kg/cubic meter. Sewage tank and clean water tank cannot be loaded and transported at the same time. Only 2600mm wheelbase can be loaded | ||
【Chassis Technical Parameters】 | |||
Chassis Model | BJ1045V9JB3-55 | Chassis name | Truck chassis |
Trademark name | Futian brand | manufacturing enterprise | Beiqi Foton Motor Co., Ltd |
Number of axes | 2 | Number of tires | 6 |
Wheelbase (mm) | 2600,2850 | ||
Tire specifications | 6.00R15 10PR | ||
Number of steel plate springs | 7/5+3,7/5+2,3/5+2,2/3+2 | Front wheel base (mm) | 1345 |
Fuel type | diesel oil | Rear wheel base (mm) | 1292 |
Emission standards | GB17691-2018 National VI | ||
Engine model | Engine manufacturing enterprises | Emissions（ml） | Power (Kw) |
Q23-95C60 Q23-95E60 | Anhui Quanchai Power Co., Ltd Anhui Quanchai Power Co., Ltd | 2300 2300 | 70 70 |
The production workshop process is shown below:
1: Clear division of labor for assembly line operations (each process is self inspected and qualified by a dedicated
person before entering the next process)!
2: All workshop welders have welding certificates (welding technicians have more than 10 years of work experience)!
3: Quality department (semi-finished product inspection, testing, pre spray testing, pre shipment testing, trial run
inspection, qualified before leaving the factory)!
4: Using manganese carbon steel plate raw materials and standard well-known brand accessories, fully automatic
welding equipment (single-sided welding double-sided forming, resistant to solid and pressure without sand)
Eye, false welding and leakage situation)!
5: Adopting advanced sandblasting and spray coating technology (sandblasting: can remove all surface rust and other
dirt, oxide layer, effectively improve the adhesion between the tank and the spray coating)
Focus and anti-corrosion ability. Spraying can make the tank display a uniform and smooth natural color, making the
appearance more beautiful and visually appealing!
Please take a look at our workshop:
Related News
Submitted successfully
We will contact you as soon as possible
